aws sqs receive-message
Retrieves one or more messages (up to 10), from the specified queue. Using the WaitTimeSeconds parameter enables long-poll support. For more information, see Amazon SQS Long Polling in the Amazon Simple Queue Service Developer Guide. Short poll is the default behavior where a weighted random set of machines is sampled on a ReceiveMessage call. Thus, only the messages on the sampled machines are returned. If the number of messages in the queue is small (fewer than 1,000), you most likely get fewer messages than you requested per ReceiveMessage call. If the number of messages in the queue is extremely small, you might not receive any messages in a particular ReceiveMessage response. If this happens, repeat the request. For each message returned, the response includes the following: The message body. An MD5 digest of the message body. For information about MD5, see RFC1321. The MessageId you received when you sent the message to the queue. The receipt handle. The message attributes. An MD5 digest of the message attributes. The receipt handle is the identifier you must provide when deleting the message. For more information, see Queue and Message Identifiers in the Amazon Simple Queue Service Developer Guide. You can provide the VisibilityTimeout parameter in your request. The parameter is applied to the messages that Amazon SQS returns in the response. If you don't include the parameter, the overall visibility timeout for the queue is used for the returned messages. For more information, see Visibility Timeout in the Amazon Simple Queue Service Developer Guide. A message that isn't deleted or a message whose visibility isn't extended before the visibility timeout expires counts as a failed receive. Depending on the configuration of the queue, the message might be sent to the dead-letter queue. In the future, new attributes might be added. If you write code that calls this action, we recommend that you structure your code so that it can handle new attributes gracefully
Options
| Name | Description |
|---|---|
--queue-url <string> | The URL of the Amazon SQS queue from which messages are received. Queue URLs and names are case-sensitive |
--attribute-names <list> | A list of attributes that need to be returned along with each message. These attributes include: All – Returns all values. ApproximateFirstReceiveTimestamp – Returns the time the message was first received from the queue (epoch time in milliseconds). ApproximateReceiveCount – Returns the number of times a message has been received across all queues but not deleted. AWSTraceHeader – Returns the AWS X-Ray trace header string. SenderId For an IAM user, returns the IAM user ID, for example ABCDEFGHI1JKLMNOPQ23R. For an IAM role, returns the IAM role ID, for example ABCDE1F2GH3I4JK5LMNOP:i-a123b456. SentTimestamp – Returns the time the message was sent to the queue (epoch time in milliseconds). MessageDeduplicationId – Returns the value provided by the producer that calls the SendMessage action. MessageGroupId – Returns the value provided by the producer that calls the SendMessage action. Messages with the same MessageGroupId are returned in sequence. SequenceNumber – Returns the value provided by Amazon SQS |
--message-attribute-names <list> | The name of the message attribute, where N is the index. The name can contain alphanumeric characters and the underscore (_), hyphen (-), and period (.). The name is case-sensitive and must be unique among all attribute names for the message. The name must not start with AWS-reserved prefixes such as AWS. or Amazon. (or any casing variants). The name must not start or end with a period (.), and it should not have periods in succession (..). The name can be up to 256 characters long. When using ReceiveMessage, you can send a list of attribute names to receive, or you can return all of the attributes by specifying All or .* in your request. You can also use all message attributes starting with a prefix, for example bar.* |
--max-number-of-messages <integer> | The maximum number of messages to return. Amazon SQS never returns more messages than this value (however, fewer messages might be returned). Valid values: 1 to 10. Default: 1 |
--visibility-timeout <integer> | The duration (in seconds) that the received messages are hidden from subsequent retrieve requests after being retrieved by a ReceiveMessage request |
--wait-time-seconds <integer> | The duration (in seconds) for which the call waits for a message to arrive in the queue before returning. If a message is available, the call returns sooner than WaitTimeSeconds. If no messages are available and the wait time expires, the call returns successfully with an empty list of messages. To avoid HTTP errors, ensure that the HTTP response timeout for ReceiveMessage requests is longer than the WaitTimeSeconds parameter. For example, with the Java SDK, you can set HTTP transport settings using the NettyNioAsyncHttpClient for asynchronous clients, or the ApacheHttpClient for synchronous clients |
--receive-request-attempt-id <string> | This parameter applies only to FIFO (first-in-first-out) queues. The token used for deduplication of ReceiveMessage calls. If a networking issue occurs after a ReceiveMessage action, and instead of a response you receive a generic error, it is possible to retry the same action with an identical ReceiveRequestAttemptId to retrieve the same set of messages, even if their visibility timeout has not yet expired. You can use ReceiveRequestAttemptId only for 5 minutes after a ReceiveMessage action. When you set FifoQueue, a caller of the ReceiveMessage action can provide a ReceiveRequestAttemptId explicitly. If a caller of the ReceiveMessage action doesn't provide a ReceiveRequestAttemptId, Amazon SQS generates a ReceiveRequestAttemptId. It is possible to retry the ReceiveMessage action with the same ReceiveRequestAttemptId if none of the messages have been modified (deleted or had their visibility changes). During a visibility timeout, subsequent calls with the same ReceiveRequestAttemptId return the same messages and receipt handles. If a retry occurs within the deduplication interval, it resets the visibility timeout. For more information, see Visibility Timeout in the Amazon Simple Queue Service Developer Guide. If a caller of the ReceiveMessage action still processes messages when the visibility timeout expires and messages become visible, another worker consuming from the same queue can receive the same messages and therefore process duplicates. Also, if a consumer whose message processing time is longer than the visibility timeout tries to delete the processed messages, the action fails with an error. To mitigate this effect, ensure that your application observes a safe threshold before the visibility timeout expires and extend the visibility timeout as necessary. While messages with a particular MessageGroupId are invisible, no more messages belonging to the same MessageGroupId are returned until the visibility timeout expires. You can still receive messages with another MessageGroupId as long as it is also visible. If a caller of ReceiveMessage can't track the ReceiveRequestAttemptId, no retries work until the original visibility timeout expires. As a result, delays might occur but the messages in the queue remain in a strict order. The maximum length of ReceiveRequestAttemptId is 128 characters. ReceiveRequestAttemptId can contain alphanumeric characters (a-z, A-Z, 0-9) and punctuation (!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~). For best practices of using ReceiveRequestAttemptId, see Using the ReceiveRequestAttemptId Request Parameter in the Amazon Simple Queue Service Developer Guide |
--cli-input-json <string> | Performs service operation based on the JSON string provided. The JSON string follows the format provided by ``--generate-cli-skeleton``. If other arguments are provided on the command line, the CLI values will override the JSON-provided values. It is not possible to pass arbitrary binary values using a JSON-provided value as the string will be taken literally |
--generate-cli-skeleton <string> | Prints a JSON skeleton to standard output without sending an API request. If provided with no value or the value ``input``, prints a sample input JSON that can be used as an argument for ``--cli-input-json``. If provided with the value ``output``, it validates the command inputs and returns a sample output JSON for that command |